Computer Hope
Internet & Networking => Networking => Topic started by: Alba on February 03, 2011, 05:47:46 AM
-
I have Windows XP, Version 2002 and Service Pack 3 (SP3)
I was downloading SP3 updates manually and during this the Windows sw advised that it needed to prepare for the install so 30min later after data clean up, creating cabinets, storing a saving data the process was complete.
Upon restarting my PC I have been unable to use Wireless which was working perfectly up until then.
I can't view any Wireless networks. Though when I start up I do get the message that 'wireless networks' are in range though I can't view them.
I've tried re-installing my ISP SW from CD and it does pick up the networks in range included that of my router but during the instal I get the message: "Wizard could not create a wireless network'.
I have tried the REPAIR facility but this does not work and I get the message that the connection ' cannot be disabled' If I try this manually I'm advised that another program could be using the connection.
I'd be grateful for any advice on this.
Thanks so much
ALBA
-
Service Pack 3 will allow for the use of WPA, perhaps you need to set it up on the routers end.
-
Thank you so much for taking the time to reply. Please excuse me for asking but could you expand on what you mean by 'setting it up at the routers end'.
Thanks again Quantos
Alba
-
Did you try restarting router, modem (if separate device) by power failing and restarting by re applying power to those devices (and your p.c., laptop)? Does your network use DHCP?
Jim
-
jcmark,
Thanks for taking the time to send me your thoughts. I have tried restarting the Laptop and the router all to no avail.
I'm in Scotland and have a basic router supplied by my ISP and so I'm not sure if I have DHCP
best wishes
Alba
-
Are you using a patch cable from your laptop to the router or are you using a different computer to access the internet?
-
jcmark,
I'm using another laptop to access the internet using the same router which proves that all is well at the router end.
Thanks
Alba
-
O.K. Set both laptops next to one another, and turn them on. Find "Control Panel" icon and mouse clik on it on both laptops. After you have the Control Panel screen on both laptops, clik on the "Network Connections" icon (or however it's listed) on both laptops. You should see "Available Networks" heading on each laptop and an icon for your wireless network on each. RIGHT clik on each wireless icon on each laptop. Is any information displayed appear to be different between the two laptops? Be careful here, don't change anything, and make any notes for future reference. Then use the cancel button to close out of these screens and close control panel. Let me know what you saw. I know this is rather tedious but I don't know how to do it any other way. By the way, on the laptop that won't communicate is there a button like a function key on the keyboard or on the back of laptop that turns on wireless function?
Jim
-
Jim,
There is hw switch on the non wireless working PC (NWPC) and when I move this I get a message to say on or off so all is OK there.
When I right click the wireless icon within NW connections the drop down menus are the same though on the NWPC I can view Status as there is not connection. I also can't disable as I get the message that the Connection may be using a protocal that does not support PLUG&PLAY. In the Wireless working PC (WPC) I can disable the connection. The WPC is an IBM T42 and the NWPC is a Lenovo X61 and the have different wireless cards.
In the NWPC the Wireless Connection Properties has AEGIS Protocol and WLAN unchecked. These are checked in the WPC though this may be due to them being different wireless adaptors. I tried checking then in the NWPC but it made no difference.
Two unusual things.
When I power up the NWPC I get the message at the bottom right of screen where the wireless icon is that
there ARE Wireless Networks in range of my PC but when I click the icon it say there are no networks in range. Also when I tried to reload my ISP router sw it does pick up a sees the address of the router but as I go through this process I'm unable to connect. So these two points suggest that the PC does in same way see the Wireless Network but when I try to view them via NW Connections there is no evidence of them.
Thanks again for you help.
Peter
-
Well...What I would do is go to the network settings on the non communicating laptop and delete that connection. You should be able to right clik the icon and delete it. Turn of the laptop and turn it back on. Does it find a new device, as in the wireless connection? If it asks re install the driver automatically you may have to do it manually instead. You should have an install disk that came with the laptop, or there is a folder on the harddrive with drivers specific to your laptops mainbord on board devices. If not you'll have to go to the mfgs. website and download the appropriate driver, using the working laptop. Then transfer that driver to the non working laptop using a USB flashdrive.
Jim
-
Jim,
I'm afraid when I right click I'm not allowed to delete the icon. Even when I press the delete key it attempts to delete, asks me if I'm sure I want to delete the Wireless Connection, but then I get the message: "The connection you selected cannot be deleted"
Peter
-
Jim,
I'm afraid when I right click I'm not allowed to delete the icon. Even when I press the delete key it attempts to delete, asks me if I'm sure I want to delete the Wireless Connection, but then I get the message: "The connection you selected cannot be deleted"
Peter
Will it let you disable the wireless NIC in either the Device Manager or the BIOS?
-
Will it let you disable the wireless NIC in either the Device Manager or the BIOS?
If that doesn''t work. Shut off the hardware network switch and try again to delete. If that doesn't work cold boot the laptop and hold down the F5 key. Pick Safe mode without network. Try to delete from control panel
-
Will it let you disable the wireless NIC in either the Device Manager or the BIOS?
Quantos: I'm a newbie here. I hope I'm not steppin on any toes.
JIM
-
Quantos: I'm a newbie here. I hope I'm not steppin on any toes.
JIM
Not at all, I just piped in with a suggestion.
-
Have you tried to rip out and reinstall the software / drivers for the wireless card? See where you stated you tried the ISP software.
If you do not have the disk for it go to the manufactures web site (for the computer) and input the systems’ serial number and download the software for the Wi-Fi card then install.
Is the NWCP showing the wireless active, disabled, is it listed under the device manager?
Can you browse the internet and or does it make a connection if connected via a cable.
You state that I can't view any Wireless networks. Though when I start up I do get the message that 'wireless networks' are in range though I can't view them. How are you trying to view them?
Make sure you are using the program that runs your wireless card to view the wireless network list.
-
You obviously have expert help here. Over and out.
Jim
-
Was able to disable using Device Manager, but still unable to delete the Wireless Icon.
Logged onto the Lenovo site and downloaded the latest version of the Intel Wireless WiFi Link 4965AG to a memory key. Tried to load this on the faulty PC to C:\DRIVERS\WIN\WLANINT and it seemed to instal. As this completed the program Intel PROSet/Wireless Software Tool Installation Wizard opened ...Preparing to install...This then failed with the message " The Windows Installer service could not be accessed. This is because of running in Safe Mode ( which I wasn't) or if the Windows Installer is not correctly installed.
Not sure what to tackle next
Thanks for your help
Alba
-
I'll wait and see what others recommend. Any attempts in the past to "fix" windows installer when I ran into issue were not successful. I have re installed XP in the past because of it. Hang on and see what recommendations you get.
-
Rustys,
Thanks for your help.
I have been able uninstall the original Wireless driver and downloaded, from the manufacturer website, the latest driver.
When I try to load this onto the faulty PC to C:\DRIVERS\WIN\WLANINT and it seemed to instal. As this completed the program Intel PROSet/Wireless Software Tool Installation Wizard opened ...Preparing to install...This then failed with the message " The Windows Installer service could not be accessed. This is because of running in Safe Mode ( which I wasn't) or if the Windows Installer is not correctly installed.
I have no appreciation as to what the issue is with the Windows Installer is.
So I'm now at the point where I have no Wireless Network Connection on the PC
Thanks
Alba
-
What is listed in Network Connections?
If the NIC is there lets try a cable and see if you can browse this way we can DL directly to the computer.
No offence you did DL the correct software for the system.Will it let you disable the wireless NIC in either the Device Manager or the BIOS?
Did you ever do this if so undo it.
-
Rustys,
Finally got the Wireless working. As you suggested I connected through Ethernet and downloaded the latest level of the Wireless driver. As previously I still got the message that the Windows Installation Tool was faulty which prevented me fully loading the Wireless Driver. So I downloaded a new version of the Installation tool and that did the trick. I was then able to fully load the driver.
Thank you for all your help.
Thanks also to jcmack and Quantos
All the best from Bonnie Scotland