Computer Hope
Internet & Networking => Networking => Topic started by: InfadaStone on January 14, 2008, 09:14:14 AM
-
Hey, I'm hoping someone can help me.
I set up a Belkin54G router on my PC so my brother could share the connection with me with his Playstation 3. We were using an unsecured network for a little while. But then I set a password because I realized someone else went on our connection. It was working fine. A day afterwards, my brother started to have problems logging into the Playstation network. Then I realized that the router said that I was connected on my PC, but when I try to load a page on internet explorer or firefox, nothing comes up. I tried to configure the firewall and disabled the NAT feature, but I still get nothing.
I'm sure the problem is with the router, be it settings or the actual hardware, because when I connect with my cable modem, I have no problems whatsoever.
I now can't access my Belkin control panel. I have to type in an IP address in IE and the panel is supposed to come up, it's not working.
I went to IPConfig and tried pinging google.com. Four Packages were sent, but none were recieved back.
Can someone tell me what happened and guide me on how to fix my router problem?
Much apreciated. x :(
-
Might be best to hard reset the router back to it's default condition, then slowly redo the settings, documenting all that you do and testing after each change is made.
Alan <>< :D
-
I can't reset to default because I can't access it's control panel. :(
Is there any other way of resetting it?
Thank you x
-
There should be a reset button on the router itself. You'll have to use a pointy object like a straightened paperclip or pen to reset it.
Alan <>< :D
-
As ale52 says it is usually just matter of inserting a pointy object into the hole containing the reset button and holding it there for 10-15 seconds. If you're having problems reseting the router consult your manual. Some brands of routers require you to press the reset button at particular point during the startup.
-
Thank you for the quick reply.
I've just reset the router like you said. Nothing's any different. I still can't get into the router control panel. I've checked that the ethernet cable is connected to the port in the back of my PC so it has a direct connection to the router.
Still nothing.
:(
-
Are you sure it got reset? Like I said some routers are picky about when to do the reset.
-
Yeah, I think so. It doesn't tell you how to reset the router in the manual. But I hold the pin in until the power light goes red. I guess that means it's done a reset. I've held it in there for longer. I can't find any other guides on how to reset a Belkin router online either.
Thanks
-
Hey! I got into the control panel after starting all over again about 100 times... But I'm in now.
The panel says that the router is connected to the internet, but I have no access to any pages online. I get "The page cannot be displayed".
I tried to ping google.com and I got the error message: Destination net unreachable, but when I ping'd my own IP, it gave me four replies.
-
Have you tried with a network cable between your computer and router?
What is the output of the ipconfig /all command?
(start->run->cmd (Enter)
ipconfig (space) /all >c:\ipcfg.txt
and then copy here the contents of c:\ipcfg.txt)
What ip has the router? (WAN ip I mean). What gateway? Can you ping the gateway? What DNS server? Can you ping the DNS servers? (you can find these informations in the status page of the router).
-
Hey, I'm already using a network cable from the PC to the router.
I can't ping the gateway. Can't ping the DNS servers either.
-
Take the router out of the loop and go directly from the modem to the computer. Does it work now? If so replace the router.
Alan <>< :D
-
Replace the network card.
Alan <>< :D
-
Hey.
The problem can't be my computer's network card. The router won't work even if I try with my brother's laptop.
I also can't use an ethernet cable with the modem I'm using right now. It's USB.
Thank you x
-
What is the output of the ipconfig /all command?
(start->run->cmd (Enter)
ipconfig (space) /all >c:\ipcfg.txt
and then copy here the contents of c:\ipcfg.txt)
What ip has the router? (WAN ip I mean). What gateway? Can you ping the gateway? What DNS server? Can you ping the DNS servers? (you can find these informations in the status page of the router).
*censored*, I reach that time in life when I quote myself :D
-
I have the same router and have had that problem several times. Reset by unplugging the power for approx 10sec. (Im sure someone wrote that in comments above I didnt read them).
I use the dynamic IP and WPA/PSK w/NAT enabled. Also back up your router settings. Belkin routers have this nature in them to loose connections sometimes and it almost seems that the BIOS or ROM chip fails sometimes. Might also change the wireless channel. That did help on my signal strength and it doesnt seem to loose the connection as often.
-
Hello there, litespeed14.
Thanks for the advice but unfortunately...
I tried all you said and my status in the corner turned into "Not Connected" after I set it to a dynamic IP setting. So I restored and I'm back to scratch. It says I'm connected but I still can't open any pages.
Anyone have any other suggestions?
-
I'm sorry, can anyone help?
-
Who is you Internet Service Provider? what is the brand name of your modem?
Have you tried turning OFF the modem and router wait like a minute then turn ON the modem 1st wait for 30sec before you power ON the router...
What is the internet IP address on the router?
-
Yes, I have tried that - no results.
ISP - Local Providers
Brand - Belkin 54g
IP - 192.168.2.1