Computer Hope
Hardware => Hardware => Topic started by: GerryRH on October 06, 2010, 01:23:45 PM
-
I've searched all the topics reasonable, nothing found like this... Got a Compaq Evo D510c. 2.4 g. Pen_IV. w/2 (1g) sticks of DDR2100 (non-ECC) RAM - but PC it is reading and reports only 1.5 gigs on board???
(oem manual specs D510c will take 2 gigs). Have chked. BIOS & run tests and the 1.5 gigs reported looks to be accurate. What brought this issue up now is some video processing I'm having to do that is pretty resource greedy and the machine is complaining about anemic 'memory'. Not to have launched a research study --- I have done a little research on the PC & RAM i'm using and nothing like "proprietary" type mem. warnings have come up.
I've tried Compaq support for their input but since the HP takeover; Compaq's (once) A#1 rated tech support has sort'a been pushed to the back row I guess. :-[
The problem was never a "come-n-go" thing. It is consistent.
A problem this steady is usually part of a pattern that generates "known issues" tech reports - does anybody know of any?
I'd sure like to get all the RAM logged on this machine that it can see (and use) - unless it was a oem M.board design FUBAR.
Thanks, Gerry
OS: XP pro
-
DLoad install and run CPU-Z and see how the RAM is reported...
Post back with the results.
-
DLoad install and run CPU-Z and see how the RAM is reported...
Post back with the results.
Hope this makes sense to you. Attached (I think) is the graphics card test page - didn't show a page of sys RAM test ?
[recovering disk space - old attachment deleted by admin]
-
Oh NO! Gpu test. Ops. I'll be back.
Gerry :o
-
Oh NO! Gpu test. Ops. I'll be back.
Gerry :o
use CPU-Z, the CPU id program.
you used GPU-Z, the GPU id program so you get nothing about your ram stick memory.
But I guess you've already figured that out :P
-
I didn't think i spelzd it wrng...
-
One more time from the top - tried to send you one html and a txt copy but, dash board on here doesn't tell you much.
Gerry
[recovering disk space - old attachment deleted by admin]
-
Post screenshots of the Memory tab and the SPD tab for both memory slots. That's 3 screenshots.
-
Memory SPD
-------------------------------------------------------------------------
DIMM # 1
SMBus address 0x50
Memory type DDR
Manufacturer (ID) Corsair (7F7F9E0000000000)
Size 512 MBytes
Max bandwidth PC2100 (133 MHz)
Part number CM64SD512-2100
Number of banks 2
Data width 64 bits
Correction None
Registered no
Buffered no
Nominal Voltage 2.50 Volts
EPP no
XMP no
JEDEC timings table CL-tRCD-tRP-tRAS-tRC @ frequency
JEDEC #1 2.0-2-2-5-n.a. @ 100 MHz
JEDEC #2 2.5-3-3-6-n.a. @ 133 MHz
DIMM # 2
SMBus address 0x51
Memory type DDR
Manufacturer (ID) PQI CORP. (7F7F7F7F7F3E0000)
Size 1024 MBytes
Max bandwidth PC2100 (133 MHz)
Part number MD641GUOE
Number of banks 2
Data width 64 bits
Correction None
Registered no
Buffered no
Nominal Voltage 2.50 Volts
EPP no
XMP no
JEDEC timings table CL-tRCD-tRP-tRAS-tRC @ frequency
JEDEC #1 2.0-2-2-5-n.a. @ 100 MHz
JEDEC #2 2.5-3-3-7-n.a. @ 133 MHz
According to CPU-Z, the first module is 512MB, not 1GB. the problem could be related to the fact that they are different manufacturers and also different timings altogether.
-
Thanks to the group: BC_Programmer - Computer_Commando - 2x3i5x. When I squinted and looked at the test report and saw the "512" I was floored (the stick has a oem label on it - 1GB DDR 2100) I don't know somehow maybe a wrong label was put on it. All I had to check it by was the computer.
Don't even remember where it was bought now!
The smack-down killer here was the little CPU-z utility. How do you find these gem anyway. I've not heard of it.
Anyway, thank you - all of you, much-in-a-half, again. SETTLED & Solved - another happy ending.
Gerry
-
Sorry you got burned on that stik of RAM...
Glad to hear you're fixed up though...