Computer Hope
Microsoft => Microsoft Windows => Windows 3.x/9x/ME => Topic started by: comda on January 17, 2010, 10:50:22 PM
-
OK I have recieved this laptop and two days before that it was running on the internet. Win 98 on a LAN card bus. How do i set this card up to run in lan? when i hook it up to the router no light apear that another connection is made i can't get on the net either.
Any Help?
-
When the laptop is on, and you insert the card into the card bus slot, does the power light come on? There should at least be some indication (a light) that the card is receiving power. If you can verify that the card is receiving power then your next step would be to make sure the driver is installed properly. To verify this, right-click on "my computer", click properties, click on the "device manager tab, and look where it says PCMCIA.. Do you see your card bus there in the list with a properly installed driver?
Once that is done, then you need to verify that tcp/ip and "client for microsoft networks" is installed. To verify this, go to control panel and click on "network". On the configuration tab, do you see tcp/ip and Client For Microsoft Networks in the list? If not, you need to get those installed... What do you see in the list?
-
OK, when i insert the card (this bus is connected to the internet through cable) (i just hope i'm talking about the right computer chip) and there is no card light. but on the task bar it shows the usb simbol and when i click it It shows "stop FE575C-3com 10/100 LAN cardbus-fast ethernet." There is a driver installed for on the control panel there is an icon that says "PC card PCMCIA" and about the list i have
-client for microsoft networks
-microsoft family logon
-windows logon
-
oh and the network is set to windows logon.
-
Ok, so the computer is recognizing the card and it's fair to say power is getting to the card.
There is a driver installed for on the control panel there is an icon that says "PC card PCMCIA"
I'm not sure what you mean by this. Did you right click "my computer", click properties, device manager tab, and verify that the driver is installed? I mean, did you actually see the name "FE575C-3com 10/100 LAN cardbus-fast ethernet." in the pcmcia category. You should see this name and there should be nothing indicating an error...
Once you confirmed this, you're going to need to add/install the tcp/ip software for the pcmcia card. Your card bus adapter should also be in that list with tcp/ip. If it is not, its a sign that the driver might not be installed. Click on "add", highlight "protocol" and click "add", highlight "microsoft" and click "add". On the right side, scroll down the list and highlight TCP/IP and click "OK". TCP/IP should then be in the list, along with "client for microsoft netowrk". At this point does your pcmcia card show up?
-
by the contro panel thing i meant to say that there is a driver for there is an icon present with the words PCMcia socet. when i add instal software (which i believe is installed) were and what do i open am i still in my computer/properties?
-
when you right-click on "my computer", click "properties, click on the "Device Manager" tab Then you'll see a list of hardware categories. Look where is says, PCMCIA. Click on the "+" sign next to that and it will display all the devices for that catagory. Do you see FE575C-3com 10/100 LAN cardbus-fast ethernet in that list??? It should be there before we proced and there should be nothing indicating an error, such as yellow exclamation marks or red question marks..
If it is not, then you'll have to find another machine with an Internet connection so you can locate and download the driver for your it.. However, sometimes, Windows provides drivers, we'll just have to see what we get here...
-
The number i see under Network adapter but under PCMCIA socket it says Toshiba ToPIC100 card bus controller
-
The number i see under Network adapter
What do you mean by this? Are you saying your FE575C-3com adapter is under the "network adapter" category? If it is, that's fine as long as NO errors apparent..
-
yes it is
-
Ok good..
Now do this:
Go to control panel and click on "network".. on the configuration tab, click on "add".. Then highlight "protocol" and click on ADD. On the left side, click on MICROSOFT, and on the right side, scroll down and highlight TCP/IP, and then click "OK"... After that, TCP/IP should be in your list on the configuration tab... Exit out of everything and restart the computer and see if you can get to the Internet...
-
nothing.
-
the router didn't show a thrid connection light anyway im out for today? G-night ttyt
-
Are you sure the cable is good?
Open a command prompt in Windows:
type: ipconfig
does it give you your default gateway (router IP address), laptop IP address, and subnet mask?
-
I'm sorry what do you mean by "your defult gateway and i will try another cable(wire once i get home) For the command Do i type that on the main computer (in which the router is connected or the laptop which i want to have internet.) because at that time i don't think there was a rounter so how will it know theres a router?
-
Open a command prompt on the laptop.. We are trying to connect the laptop to your router using your new pc card..so when we use the ipconfig command, it will tell us a lot about the state of your laptops connectivity... It doesn't matter if the laptop was never connected to a router before...
If it gives you a default gateway address (the default gateway address is the IP address for the router...You'll know what I mean when you use the command), ip address, and subnet mask... Then we have determined that your cable is good because if the cable wasn't good then the dhcp server on your router would not be able to assign your computer an ip address... In other words, it could just be that a link light is out on your router...
However, the cable could still be good if you don't have an ip address assigned to your computer (as indicated with the IPCONFIG command), we would simply have to isolate the problem further... However, having no link light on the router when connecting is a good sign that the cable is not send/receiving and that the cable could be bad...
-
its not a new card, the prevous owner used the card 2 days before she gave it to me and about the router. When i hook up a connection the router light indicates theres a conection even when the computer is off. But it won't with this one. by the way do i do this in dos when i have it plugged into the net?
-
While the router is on and the cable is connected...From the desktop, click START, click on RUN,
type: command
press enter
when you are at the prompt, type: ipconfig and press enter
What is the output? Does it give you a default gateway address, IP address, and subnet mask ?
-
Oh i'm sorry looks like the cable wasn't working for i'm using the laptop to type this now. Thank-you EEVIAC for all your help ;D Just one last question. Will the same format work on a win95 NEC laptop?
-
Glad it's working now :)
Honestly, the last time I used Windows 95, I was in high school and I'm not familiar with it, but I suspect the configuration would virtually be the same..