Welcome guest. Before posting on our computer help forum, you must register. Click here it's easy and free.

Author Topic: Blue Screen!!!  (Read 9274 times)

0 Members and 1 Guest are viewing this topic.

boytheracer

    Topic Starter


    Starter

    Blue Screen!!!
    « on: May 14, 2008, 02:40:37 PM »
     Good evening all.

    Had downloaded service pack and was installing when a message came up about where to put a file named **boot.sys so i canclled the install, restarted my computer, it went to a screen saying somthing like restoring system configuration, then we blue screened with the message saying:

    STOP: c000021a {Fatal System Error}
    The Windows Logon Process system process terminated unxpectedly with a stats of 0xc0000006 (0x00000000 0x00000000).
    The system has been shut down

    ** means i do not recall the first couple of letters

    Any help would be much appreciated, thank you all in advance

    patio

    • Moderator


    • Genius
    • Maud' Dib
    • Thanked: 1769
      • Yes
    • Experience: Beginner
    • OS: Windows 7
    Re: Blue Screen!!!
    « Reply #1 on: May 14, 2008, 03:12:19 PM »
    " Anyone who goes to a psychiatrist should have his head examined. "

    boytheracer

      Topic Starter


      Starter

      Re: Blue Screen!!!
      « Reply #2 on: May 14, 2008, 04:05:25 PM »
      Operating system = windows xp sp2
      error message = above
      Basic details = Dell, 512, 1.6ghz centrino, cant think of anything else sorry

      i think everything else is covered above

      Thanks

      programming_pat



        Apprentice

      • I like Rabbits and Guinea pigs
        Re: Blue Screen!!!
        « Reply #3 on: May 14, 2008, 05:21:01 PM »
        boot.sys is a file that is neededfor windows startup. if you have a windows xp install disk, you need to use the recovery console and replace the file.

        patio

        • Moderator


        • Genius
        • Maud' Dib
        • Thanked: 1769
          • Yes
        • Experience: Beginner
        • OS: Windows 7
        Re: Blue Screen!!!
        « Reply #4 on: May 14, 2008, 05:23:20 PM »
        Was this Service Pack 3 ? ?
        There are some issues with it.
        Can you boot into safemode ? ?
        Have you installed any software/hardware recently other than the SP ? ?
        " Anyone who goes to a psychiatrist should have his head examined. "

        boytheracer

          Topic Starter


          Starter

          Re: Blue Screen!!!
          « Reply #5 on: May 15, 2008, 02:22:42 AM »
          Sorry i thought it said SP3 in the title. Not cannot boot in safe or on last known config. No new soaftware has been installed recently, maybe a fash or shockwave but that all i can think about.

          Many thanks

          naresh.techie



            Rookie

            Re: Blue Screen!!!
            « Reply #6 on: May 22, 2008, 03:52:53 AM »
            HI

            CAUSE
            The STOP 0xC000021A error occurs when either Winlogon.exe or Csrss.exe fails. When the Windows NT kernel detects that either of these processes has stopped, it stops the system and raises the STOP 0xC000021A error. This error may have several causes. Among them are the following:• Mismatched system files have been installed.
            • A Service Pack installation has failed.
            • A backup program that is used to restore a hard disk did not correctly restore files that may have been in use. 
            • An incompatible third-party program has been installed. 


            RESOLUTION
            To troubleshoot this problem, you must determine which of these processes failed and why.

            To determine which process failed, register Dr. Watson as the default system debugger (if it is not already the default debugger). Dr. Watson for Windows NT logs diagnostic information about process failures to a log file (Drwtsn32.log). Also, you can configure this program to produce memory dump files of failed processes that you can analyze in a debugger to determine why a process fails.

            To set up Dr. Watson to trap user-mode program errors, follow these steps: 1. At a command prompt, type System Root\System32\Drwtsn32.exe -I, and then press ENTER.

            This command configures Dr. Watson as the default system debugger.
            2. At a command prompt, type System Root\System32\Drwtsn32.exe, and then select the following options:
            Append to existing log file
            Create crash dump
            Visual Notification
             
            3. After the computer restarts from the STOP 0xC000021A error, run Dr. Watson (Drwtsn32.exe).
            4. View the Dr. Watson log to determine what user mode process may be causing the problem.
            5. If the Dr. Watson log does not contain sufficient information to determine the cause of the problem, analyze the User.dmp file to determine the cause of the STOP 0xC000021A error.

            If Dr. Watson did not create a User.dmp file for either Winlogon.exe or Csrss.exe, you may have to use a different tool to generate a memory dump file of the process that fails. For more information, click the following article number to view the article in the Microsoft Knowledge Base:
            241215 (http://support.microsoft.com/kb/241215/) How to use the Userdump.exe tool to create a dump file
            Note Follow the instructions in the Knowledge Base article to troubleshoot a process that shuts down with an exception. While you follow these instructions, monitor the following processes to troubleshoot the STOP 0xC000021A error: • Winlogon.exe
            • Csrss.exe
            Note Most STOP 0xC000021A errors occur because Winlogon.exe fails. This typically occurs because of a faulty third-party Graphical Identification and Authentication (GINA) DLL. The GINA is a replaceable DLL component that Winlogon.exe loads. The GINA implements the authentication policy of the interactive logon model. The GINA performs all identification and authentication user interactions. 
            It is very common for certain types of remote control software to replace the default Windows GINA DLL (Msgina.dll). Therefore, a good first step is to examine the system to see if it has a third-party GINA DLL. To do this, locate the following registry key:
            HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon
            Value = GinaDLL REG_SZ

            • If the Gina DLL value is present and if it is anything other than Msgina.dll, it probably means that a third-party product has changed this value.
            • If this value is not present, the system uses Msgina.dll as the default GINA DLL.
            If this error first occurred after the installation of a new or updated device driver, system service, or third-party program, the new software should be removed or disabled. Contact the manufacturer of the software to see if an update is available. For information about how to contact the manufacturer of the software, click the appropriate article number in the following list to view the article in the Microsoft Knowledge Base:
            65416 (http://support.microsoft.com/kb/65416/) Hardware and Software Third-Party Vendor Contact List, A-K

            60781 (http://support.microsoft.com/kb/60781/) Hardware and Software Third-Party Vendor Contact List, L-P

            60782 (http://support.microsoft.com/kb/60782/) Hardware and Software Third-Party Vendor Contact List, Q-Z
            Last known good configuration
            If the previous steps in this article do not resolve the problem, start the computer by using the last known good configuration. To start the computer by using the last known good configuration, follow these steps:Note Because there are several versions of Microsoft Windows, the following steps may be different on your computer. If they are, see your product documentation to complete these steps. 1. Click Start, and then click Shut Down. 
            2. Click Restart, and then click OK. 
            3. Press F8 at the indicated time: • For an x86-based computer: When a screen of text appears and then disappears , press F8. (The screen of text may include a memory test, lines about the BIOS, and other lines.) There may also be a prompt that tells you when to press F8. 
            • For an Itanium architecture-based computer: After you make your selection from the boot menu, press F8. There may be a prompt that tells you when to press F8. 
             
            4. Use the arrow keys to select Last Known Good Configuration, and then press ENTER.

            NUM LOCK must be off before the arrow keys on the numeric keypad will function.
            5. Use the arrow keys to highlight an operating system, and then press ENTER.
            Notes• Choosing the Last Known Good Configuration startup option provides a way to recover from problems such as a newly added driver that may be incorrect for your hardware. However, it does not solve problems that are caused by corrupted or missing drivers or files.
            • When you choose the Last Known Good Configuration option, only the information in registry key HKLM\System\CurrentControlSet is restored. Any changes you have made in other registry keys remain. 

            In-place upgrade
            If the previous steps in this article do not resolve the problem, perform an in-place upgrade. For more information about how to do this,, click the following article numbers to view the articles in the Microsoft Knowledge Base:
            292175 (http://support.microsoft.com/kb/292175/) How to perform an in-place upgrade of Windows 2000
            315341 (http://support.microsoft.com/kb/315341/) How to perform an in-place upgrade (reinstallation) of Windows XP
            816579 (http://support.microsoft.com/kb/816579/) How to perform an in-place upgrade of Windows Server 2003
            Remove incompatible software by using the Recovery Console
            If the previous steps in this article do not resolve the problem, remove incompatible software by using the Recovery Console. Complete steps that describe how to do this are beyond the scope of this article. However, you may be able to use the following articles as guidelines for performing this procedure.
            313670 (http://support.microsoft.com/kb/313670/) How to replace a driver by using Recovery Console in Windows 2000
            816104 (http://support.microsoft.com/kb/816104/) How to replace a driver by using Recovery Console in Windows Server 2003
            326215 (http://support.microsoft.com/kb/326215/) How to use the Recovery Console on a Windows Server 2003-based computer that does not start
            229716 (http://support.microsoft.com/kb/229716/) Description of the Windows 2000 Recovery Console
            307654 (http://support.microsoft.com/kb/307654/) How to install and use the Recovery Console in Windows XP
            307545 (http://support.microsoft.com/kb/307545/) How to recover from a corrupted registry that prevents Windows XP from starting
            216417 (http://support.microsoft.com/kb/216417/) How to install the Windows Recovery Console