Web pages with advertisements stall both IE and Firefox?

[Broni]

Did you run hard drive diagnostic?

[Beedub245]

I will not be where that computer is until around 9:00EST.  I will run tests when I get there.  Reinstalling XP is just something that I have been thinking about doing for awhile now as a means of getting rid of all those fragments of AOL, NetZero, wal mart online software, etc.  that was installed while the cpu was not in my possession.

[Broni]

First, your hard drive has to check out. Then you'll worry about other things.

[Beedub245]

Okay I am here now and working on this.  Trouble is I do not know what kind of hard drive I have.  I am trying to figure it out without opening it up.  I made a HiJack This log before everything stopped working.  Is there any info in that log that pertains to the type of hard drive that I have?

[Beedub245]

I cracked it open.  I have a Samsung hard drive.  Downloaded CD-Rom, because I don't have a floppy drive.  Downloaded ImgBurn.  When I go to advanced to make the disc bootable I get some other options(boot image, developer ID, load segment, and sectors to load) do I need to do anything to these options or just leave them alone? Also, this will work using a dvd right?  I believe I am out of blank cd-r's.  Sorry if I am being a hassle.

[Broni]

Leave all settings alone.
I've never used DVD, but it should work, I think.

[Beedub245]

Thank you for your help so far.  I have made the DVD and it is running.  What info am I looking for?

[Broni]

If it'll find errors, it'll tell you.

[Beedub245]

I get Add a new hard disk, install existing hard disk, maintenance options(-->create an ontrack boot diskette, update mbr boot code, backup or restore mbr), utilities(-->copy a partition, set hard drive size, zero fill drive(full),zero fill drive(quick)), Hard Disk Information(-->display technical hard drive information, view hard drive jumper settings)
I chose hard disk information and then selected my drive.  I was given the following:

IDE Information
Size
LBA Sectors                   312581808(160.04 GB)           CHS   16383 X 16 X 63 (8.46GB)
DMA
MW DMA SUPPORT           0,1,2             MW DMA Active
MW DMA CYCLE TIME       120 ns       Min. Cycle/Word            120 ns
UltraDMA Support       0,1,2,3,4,5,6                   UltraDMA ACtive            5

Misc.
Firmware Rev.                TM100-2
S.M.A.R.T. Support             Enabled
ATA-# Supported         7,6,5,4,3,2      IORDY Support           YES
R/W Multiple                 YES        Sectors/Block            16
PIO Mode Support              3,4               PIO Cycle Time            120ns


Translation Information
MBR Partition Table
Type        Bootable        Begin CHS          End CHS              Size
B                true                0 1 1              842 239 63            6.53 GB
7               false              843 0 1           20671 239 63        153.51 GB
0               false                0 0 0               0 0 0                        0
0               false                0 0 0               0 0 0                        0

Translation
CHS Values         BIOS          XBIOS Logical          XBIOS Physical
Cylinders            20673          19457                      16383
Heads                   240              255                         16
Sectors/Track         63               63                           63

Everything look okay?  Also, I noticed that when I changed the boot order there was not anything in position 1, hard disk was in position 2, cd rom was in position 3, and nothing was in position 4.  Is it normal for the first slot to not be used?  I appreciate any help you can give me on the next steps to take.  Thanks

[Broni]

I'm little bit confused.
Was any test ran?

[Beedub245]

There wasn't a test option in that program.  I downloaded another program that has a testing option and it is running now.  I passed all of the initial tests, but now that I am running the full scan I am getting a lot of Ecc and media errors in C:4544

[Beedub245]

Numerous ECC and Media errors were found in the full scan.  Is there any way to correct these or is it a lost cause?

[Broni]

I'm not sure. Which Samsung test are you using?
Can you post exact error(s)?