Author Topic: Installed new DVD Burner / Now CD Burner won't work (Read 12939 times)

Evenflow · « **on:** October 28, 2010, 06:35:27 PM »

I recently installed a new dvd burner in my computer. I already have a CD burner in it which was read under the E drive. The dvd burner reads D drive, but now I no longer have an E drive with my cd burner. How do I get it back installed ?

Ironman · « **Reply #1 on:** October 28, 2010, 10:45:42 PM »

You have to go to your computer's BIOS settings and change the settings of the new CD drive and change it settings from a "Master" drive to a "Slave" drive. "Master" meaning primary and "Slave" secondary. BIOS stands for "basic input/output system" and it's how your computer interfaces with the hardware. You can enter your computer BIOS during start-up using a specific keyboard key like "F11" or "F8" but the key varies on different motherboards(which is the main hardware that controls the crucial aspects of the computer) based on their manufacturer . If you could provide the specifications of your computer I could provide a step by step tutorial based on what type of motherboard you have to change you CD Drive settings.

patio · « **Reply #2 on:** October 28, 2010, 11:08:32 PM »

The master/slave settings are NOT controlled in the BIOS so you can safely ignore the above advice...
You need to double check how the drives are connected and jumpered...and let us know whether they are IDE drives or SATA...

If IDE they need to be jumpered and connected as follows if on the same ribbon cable:

MBoard============================================Slave===========Master.

Let us know...

Ironman · « **Reply #3 on:** October 28, 2010, 11:17:18 PM »

Quote from: patio on October 28, 2010, 11:08:32 PM

The master/slave settings are NOT controlled in the BIOS so you can safely ignore the above advice...
You need to double check how the drives are connected and jumpered...and let us know whether they are IDE drives or SATA...

If IDE they need to be jumpered and connected as follows if on the same ribbon cable:

MBoard============================================Slave===========Master.

Let us know...

My bad I made the post hastily, the BIOS can tell info on which drive is slave or master, to change it you have to physically do that:

IDE:
http://freepctech.com/pc/001/installing_ide_devices.shtml

SATA
http://www.seagate.com/ww/v/index.jsp?locale=en-us&name=install-troubleshoot-sata-non-mac&vgnextoid=2b089d2c3c90e010VgnVCM100000dd04090aRCRD

mroilfield · « **Reply #4 on:** October 29, 2010, 04:11:55 AM »

Ok I didn't know that CD and DVD drives required a slave/master type set up. I guess you learn something new every day.

Evenflow · « **Reply #5 on:** October 30, 2010, 11:12:29 AM »

Thank you guys for your help. I'm not an expert on computers, but from your suggestions it looks like my connections are correct. I already had an NEC DVD burner in my computer that went bad and I replaced it with a samsung DVD burner. So basically I just swaped them out and made the same connections that they were in. It's just that before my CD player/burner worked which showed it on an E: drive and now it doesn't show an E: drive and it won't work. The DVD burner works fine though and shows it as normal on the D: drive.

Evenflow · « **Reply #6 on:** October 30, 2010, 11:21:07 AM »

Like I said, I'm not a computer whiz but the connections look like IDE according to the illustration that was posted. Thanks.

Computer_Commando · « **Reply #7 on:** October 30, 2010, 11:32:04 AM »

Verifying the CD-ROM cables are correctly connected

Salmon Trout · « **Reply #8 on:** October 30, 2010, 11:54:07 AM »

Quote from: mroilfield on October 29, 2010, 04:11:55 AM

Ok I didn't know that CD and DVD drives required a slave/master type set up. I guess you learn something new every day.

All IDE devices need this. Two masters or two slaves on the same cable will cause a problem.

Evenflow · « **Reply #9 on:** October 30, 2010, 12:15:50 PM »

Why didn't I have the same problem before I swaped out DVD burners ? It started happening when I installed the new one. Same connections.

Computer_Commando · « **Reply #10 on:** October 30, 2010, 12:39:02 PM »

http://www.pcguide.com/ref/hdd/if/ide/confCable80-c.html

Evenflow · « **Reply #11 on:** October 30, 2010, 02:05:06 PM »

Thanks Computer_Commando. So by installing the new DVD burner it affected the cable ribbon to be outdated ? My computer is an older model Dell which I bought in 2004 with the CD & DVD player/burners installed by Dell to my order specs. when I bought it.

OpenSource · « **Reply #12 on:** October 30, 2010, 03:01:27 PM »

I doubt that the ribbon is oudated. Do your drives show up in the BIOS or do they just not show up in windows?

Evenflow · « **Reply #13 on:** October 30, 2010, 03:09:40 PM »

I'm a half-wit with a lot of computer stuff. How do I get to the BIOS to check that ?

OpenSource · « **Reply #14 on:** October 30, 2010, 03:16:00 PM »

When you start your computer up, it will say (press something to enter setup). Usually it's F1 or F2 or DEL. Once you're in your BIOS, it will indicate everything that's connected to the different interfaces on your motherboard; IDE0 or IDE1 with a bunch of numbers next to them but you will probably see 3 things: Your HDD, your CD drive and your DVD drive if you have it connected right. If you only see 2 devices connected to all of your IDE interfaces, then you have a problem with your jumpers or your cable. I would put all your jumpers to cable select (CS) if you don't see the devices and make SURE everything is plugged in right...the cable, the power, the jumper.

Evenflow · « **Reply #15 on:** October 30, 2010, 03:42:30 PM »

Okay, I went into the Bios. I hope this is the correct info. that your telling me to check. On my drive configuration it had............

Diskette Drive A: 3.5 Inch, 144 MB
Primary Master Drive............Hard Drive
Primary Slave Drive..............Off
Secondary Master Drive.........CD-ROM Device
Secondary Slave Drive...........Unknown Device

IDE Drive UDMA..........ON

Also, Showing when I go into My computer I also have listed a drive ( F: ) Which says Removable Disk, which I didn't have before I put the new DVD drive in.

OpenSource · « **Reply #16 on:** October 30, 2010, 03:50:42 PM »

Unknown device eh? Well at least something is showing up. What kind of DVD burner do you have?

Evenflow · « **Reply #17 on:** October 30, 2010, 03:57:51 PM »

A cheapee Samsung SH-S222L 22X LS. I ordered it from Newegg. So far it works fine and it shows up on the ( D: ) drive.

patio · « **Reply #18 on:** October 30, 2010, 04:13:57 PM »

Have you checked the jumpers on each drive and cabled them as suggested ? ?

Not a perfect image here but it may help:

NOTE: All drives are different....look for diagrams on the plastic case above the jumper position...

Evenflow · « **Reply #19 on:** October 30, 2010, 04:33:10 PM »

Like I said before.....I'm not a whiz....don't make fun of me but, you are talking about my hard drive to check this....right ?

patio · « **Reply #20 on:** October 30, 2010, 04:34:42 PM »

No...both Optical drives...

Thats why i mentioned it wasn't the perfect image...but would help.

And we don't make fun...our job is to help educate.

Evenflow · « **Reply #21 on:** October 30, 2010, 05:24:57 PM »

Okay, I'll have to unhook everything again and check this out. Thank you for all your help.

Computer_Commando · « **Reply #22 on:** October 30, 2010, 05:44:11 PM »

CD-ROMS are labeled MS, SL, CS, punched into the metal case above the jumper block. Not always easy to see, but it's there.

JJ 3000 · « **Reply #23 on:** October 30, 2010, 11:55:50 PM »

Here's a pic of a CD drive jumpered as slave. It should help you figure this out.

Computer Hope Forum

News:

Author Topic: Installed new DVD Burner / Now CD Burner won't work (Read 12939 times)

Evenflow

Ironman

patio

Ironman

mroilfield

Evenflow

Evenflow

Computer_Commando

Salmon Trout

Evenflow

Computer_Commando

Evenflow

OpenSource

Evenflow

OpenSource

Evenflow

OpenSource

Evenflow

patio

Evenflow

patio

Evenflow

Computer_Commando

JJ 3000